Straumann Tissue Level

Straumann Tissue Level®

We have five sizes.

T-7101 - ∅ 3,5
T-7102 - ∅ 4,8
T-7103 - ∅ 4,8 Synocta
T-7104 - ∅ 6,5
T-7105 - ∅ 6,5 Synocta

We have the following options in the Implant Library:

T-7101
T-7101 E
T-7101 NON E

T-7102 (A h:12.50mm)
T-7102 E
T-7102 E ZR
T-7102 NON E TYPE A
T-7102 NON E ZR TYPE A
T-7102 NON E TYPE B
T-7102 NON E ZR TYPE B
T-7102 NON E TYPE C
T-7102 NON E ZR TYPE C
T-7102 E deep
T-7102 E ZR deep
T-7102 NON E TYPE A deep
T-7102 NON E TYPE B deep

T-7102 (B h:12mm)
T-7102 E
T-7102 E ZR
T-7102 NON E TYPE A
T-7102 NON E ZR TYPE A
T-7102 NON E TYPE B
T-7102 NON E ZR TYPE B
T-7102 NON E TYPE C
T-7102 NON E ZR TYPE C
T-7102 E deep
T-7102 E ZR deep
T-7102 NON E TYPE A deep
T-7102 NON E TYPE B deep

T-7102 (C h:13.10mm)
T-7102 E
T-7102 E ZR
T-7102 NON E TYPE A
T-7102 NON E ZR TYPE A
T-7102 NON E TYPE B
T-7102 NON E ZR TYPE B
T-7102 NON E TYPE C
T-7102 NON E ZR TYPE C
T-7102 E deep
T-7102 E ZR deep
T-7102 NON E TYPE A deep
T-7102 NON E TYPE B deep

T-7103
T-7103 E old
T-7103 E ZR old
T-7103 NON E
T-7103 NON E ZR
T-7103 E new
T-7103 E ZR new

T-7104
T-7104 E
T-7104 E ZR
T-7104 NON E TYPE A
T-7104 NON E ZR TYPE A
T-7104 NON E ZR TYPE B
T-7104 NON E TYPE B

T-7105
T-7105 E
T-7105 E ZR
T-7105 NON E TYPE A
T-7105 NON E ZR TYPE A

Clarifying Notes

E = Engaging.
NON E = Non Engaging.
When we want to use the library to produce zirconium structures must select options with the ZR letters.
TYPE A = the connection is deeper and it is advised to use in cases with good parallelism. (Picture 1.)
TYPE B = the connection is shorter and it is advisable to use in cases of bad parallelism. (Picture 2.)
TYPE C = the connection is very shorter and it is advisable to use in cases of very bad parallelism. (Picture 3.)
deep = that the design is ready to use the screw "Basal". See in Website Store. Click here (Picture 4.)
new = that we are using the new Scanbody. See the photos to identify the Scanbody. (Picture 5.)
old (Sometimes the word "old" is omitted. In ref. T-7102) = that we are using the old Scanbody. See the photos to identify the Scanbody. (Picture 6.)
Use this link to see in detail the types of Scanbodies. For identification. It is very important to see Click Here !
Very Important:
In these references T-7102 there are 3 types of Scanbodies.(Depending on the height)
T-7102
Use your Scanbodies in the following way:
You should measure, for full security model you are using. According picture.
-The most used is the type A. It measures 12.50mm
-The type B measures 12mm
-The C type (that is the least common) should measure 13.10mm
See photos below.
Target3D is not responsible if all instructions are not followed.
ScanJig%20H.pngDetall.png
In these references T-7103 there are two types of Scanbodies.
T-7103
-When the reference says old, you must use the "Old"
-When the reference says new, you must use the "new"
In this case in Non Engaging references can be used interchangeably.
T-7105
-You need to use the original Wn Analog . You need to place a pillar synOcta Rn to use it. (Picture 7, 8)
It is advisable to test these options in order to choose the most appropriate to each one when needed.

These options can be used in combination of each other.

ScreenShot398.jpgScreenShot397.jpgScreenShot399.jpg11.06.28.png Wn%20Analog%281%29.jpg 7 Wn Analog with Synocta Rn Wn%20Synocta%20Scanbody.jpg 8 Wn Synocta Scanbody
Unless otherwise stated, the content of this page is licensed under Creative Commons Attribution-ShareAlike 3.0 License